Plastic Film machinery

NoDescriptionQuantityPrice[USD]Amount[USD]1. SJGM-Z35×30×2+45×30×1-850mm Plastic extruder unit Die Head unitAir Ring Unit Haul-off UnitCollapse unitSize cage unit Winder unitElectrical Control System1 set2. PRICE: FOB DALIAN USD /SET SJGM-Z35×30×2+45×30×1-850mm Technical data and price A. Basic Specification Film folds flat width: 550mm Raw material: LDPE\ LLDPE \HDPEFilm thickness(single- side): 0.20mm(LDPE),0.10MM(HDPE) Max Film. Extrusion Output: 100kg/h Overall dimension (l×w×h): 8000*4200*6600mm Total power of the line: approx. 105KW, about 55KW in regular working condition, 380V (-10% +5%) /3phase/50 Hz Weight of the line: approx 8000kg, 1 sets 40` container needed SJGM-Z35×30×2+45×30×1-850mm Technical data and price 1. Plastic extruder 1.1 Screw diameter: 35mm, the power of drive motor is 15KW; 2 sets Screw diameter: 45mm, the power of drive motor is 22KW; 1 sets 1.2 L/D ratio: 30:1(complex mixing structure, be suitable for the material of LDPE\ LLDPE \HDPE), the speed of the screw is 13 120/min; 1.3 The material of screw and barrel and hardness: 38CrMoAlA steel nit riding, bimetal. more than HV860 1.4 The controller of the drive motor: HITACHI inverter 1.5 Reducer: with movers hard tooth surface for extruder special gear box ,triaxial transmission and double reduction, external connecting the recycle cooling water wheel pump with forced lubrication gear box; 1.6 The cooling type of barrel: the feeding section with the water shielding to control the Temperature, the rest equipment the cooling fan with 370W; 1.7 The heat type ,tem. Control and zone stage :the heater inner trench type cast aluminum ,four stage, with K type thermoelectric pair to measure temperature ,the out cover of barrel adopt the stainless steel; 1.8 The rapid Screen changer: manually operation swing arm type; 1.9 The display unit for inner pressure: pressure gauge in pointer type to monitor the pressure of high tem. Material; 1.10 The hopper: the stainless steel material, with window and the slippage device which is convenient for unloading the material, the capacity is 50kg; 1.11 The base of hopper: with the forced feeding device through the cooling water 1.12 The max. Extrusion output of 45mm extruder (LDPE) is 50kg/h The max. Extrusion output of 35mm extruder (LDPE) is 40kg/h 2. Die Head Unit 2.1 Die- head structure: co-3-layer co-extrusion complex, and spiral mandrel structure;The die-head no rotating, 2.2 The material of the die-head: 40Cr, finishing polish with plate hard Cr and polish once; 2.3 The diameter of the moulds: 220mm(LDPE),160mm(HDPE), the machining and designing precision mould can confirm the gloss finish of the spiral flow passage; 2.4 The stage of die-head heater and power: 3 zone independently control, the protect porcelain-head is installed on the post head of the heater; 3. Air Ring Unit 3.1 The type of the vane: the vane with double air course, with the wind input in side direction and the aerodynamic make-up type, 3.2 The blower of vane: the low noise blower with the power is 5.5KW, 1sets HITACHI inverter controller; 4. Haul-off Unit 4.1 The traction frame with framework assemble and four inner walking platform, it’s convenient to assemble and install and heavy building 4.2 The height of the traction: 6600mm,the height of the guardrail is 1100mm,add the 30mm the mouth of the frame cover to the edge of inner and outside walking platform, install the ledge for load or unload haul off roll in the up-take-off platform 4.3The width of haul off roll 850mm,the surface of the initiative steel roller plate hard chrome and machining polish, the open and close of the Paul -off controlled by air control, the up-take-off roller adopt the excellent robber , anti-chap and shed.